An original three-character collection produced in gold plated hard enamel, with every enamel color polished flush to the metal rim. Designed for gift shops, museum stores, subscription boxes, bookstores and brand merch programs. Minimum order: 50 pieces per design.

What separates a hard enamel pin from a cheap imitation is not the artwork — it is what happens after the colors go in. Every piece is filled, baked, then sanded and buffed until the enamel sits level with the metal ridges. The result is a single glass-smooth plane you can feel with a fingertip.

These macro shots are the same five checkpoints our QC team uses before a carton leaves the floor. If a supplier cannot show you these views, the sample will look different from the bulk order.
After polishing, a continuous highlight line should run along the entire rim. Over-buffing thins that line; under-buffing leaves a step that feels rough against skin. This is the first thing to inspect on a sample.
Two adjacent enamel colors are separated by a gold divider of roughly 0.8 mm. Colour bleeding, a covered divider or a jagged edge all point to rushed filling and a wrong curing curve.
The feather marks run 0.4–0.5 mm. At this scale, mold accuracy decides everything: lines that merge into a blob, or recesses that are not fully filled, are visible to the naked eye at arm's length.
Eye highlights, cheek dots and the beak tip are three separate fills that must land exactly on target. A highlight that drifts off-center instantly makes the character look wrong.
Over forty closely spaced gold quills make this the most demanding area of the set. The two failure modes are bridging between lines and trapped air bubbles that show up as white specks after curing.
Check four things: is the post vertical, is the solder a small even fillet, is the back fully plated, and does the clutch grip firmly without biting into fabric.
Both are legitimate products at different price points. Knowing the difference prevents the most common disappointment in a first enamel pin order.
| Property | Hard enamel (this product) | Soft enamel |
|---|---|---|
| Surface | Flat and glass-smooth; enamel polished level with the metal | Textured; enamel sits below raised metal lines |
| Feel | One continuous plane, with no ridges to catch a fingernail | Lines feel raised and colors feel recessed |
| Scratch resistance | Higher — the flat surface resists daily wear and polishing | Lower — recessed color is more vulnerable to abrasion |
| Look under light | Even sheen across the whole piece; premium jewelry feel | Uneven sheen with shadows in the recesses; more sculpted |
| Production | Filling plus baking plus sanding plus buffing; more steps, higher reject rate | Filling and baking only; faster and cheaper |
| Typical price | Roughly 30–50% above soft enamel of the same design | Entry price point |
| Recommended for | Retail display, gift packaging, brand merch, collectibles | High-volume giveaways, events, low-budget promo |
| Product name | Woodland Friends hard enamel pin set (fox / owl / hedgehog) |
|---|---|
| Category | Custom lapel pin, enamel badge, cloisonné style pin |
| Base material | Die-cast zinc alloy |
| Enamel type | Hard enamel, oven cured, polished flush |
| Plating | Gold (default); silver, rose gold, black nickel, antique bronze on request |
| Size | 30–35 mm (1.18–1.38 in) per character; custom sizes 20–45 mm available |
| Thickness | 1.2–1.5 mm metal body |
| Colors | 8 enamel colors in this set; up to 12 supported per design |
| Minimum line width | 0.4 mm |
| Attachment | Butterfly clutch on a soldered brass post |
| Edge finish | Rounded and deburred, smooth to the touch |
| Packaging | OPP bag standard; kraft backing card or printed card optional |
| Minimum order | 50 pieces per design |
| Artwork required | AI, EPS, PDF or SVG vector; 300 dpi PNG accepted and vectorized in-house |
| Proofing | Free digital proof before sampling |
The three animals are original artwork. Use them as-is, or send your own character line and we will adapt the same construction.
| Option | Range |
|---|---|
| Shape | Free-form outline cut to your artwork, no extra die charge for standard shapes |
| Size | 20 mm to 45 mm; larger sizes quoted separately |
| Colors | Up to 12 solid colors; Pantone matching to nearest reference |
| Plating | Gold, silver, rose gold, black nickel, antique bronze, matte gold |
| Effects | Glitter fill, glow-in-the-dark, pearl accent, printed gradient |
| Backing | Butterfly clutch, rubber clutch, double post, magnetic back, safety pin |
| Packaging | OPP bag, kraft backing card, printed display card, barcode label, poly mailer |
| Sets | Single character or three-piece set in one retail card |
No account setup, no minimum artwork complexity. Send a file and you will see a proof before anything is charged for tooling.
Vector file or a clear image. We reply with feasibility notes on line width, color count and size.
A digital proof shows exact colors, plating and dimensions. Revisions are free until you approve.
A physical sample is produced for sign-off. Bulk production only starts after your written approval.
Full run, QC against the approved sample, then individual bagging and carton packing.
| Stage | Typical lead time | What you receive |
|---|---|---|
| Digital proof | 1–2 business days | Color and size proof for approval |
| Sample | 7–10 days | One physical piece per design |
| Bulk production | 12–18 days after sample approval | Full order, QC checked |
| Packing | 2–3 days | Individual bagging, backing cards, cartons |
Lead times are indicative and confirmed per order after the artwork is reviewed. Peak season and complex designs may extend them.

The flat polished surface is the practical advantage of hard enamel: it does not collect lint, it wipes clean, and it survives being worn on a jacket every day.
Short, direct answers to the questions that come up in almost every enamel pin inquiry.
The minimum order is 50 pieces per design. Colors, plating and backing can be mixed within one design, but each distinct artwork is counted separately. Mixed sets of the three Woodland Friends characters count as three designs unless they share one die-cut outline.
They are hard enamel. Each color is filled into its recess, cured, then the entire face is sanded and buffed until the enamel is level with the metal ridges. The result is a flat, glossy surface with no raised lines — the standard used for retail and collectible pins.
Yes. The Woodland Friends artwork is original and can be licensed for your order, or you can send your own character, logo or illustration. Send AI, EPS, PDF or SVG; a high-resolution PNG or a photo of a sketch is also accepted and redrawn as vector artwork before proofing.
The minimum reliable line width is 0.4 mm. Below that, lines tend to merge during die-casting and the enamel cannot be filled cleanly. The hedgehog quills and owl feather marks in this set sit right at that limit as a demonstration of what the mold can hold.
Up to 12 solid colors per design. This set uses 8. Each additional color adds one filling and curing cycle, so cost rises with color count — six to eight colors is the usual sweet spot for detailed characters.
A digital proof takes 1–2 business days, a physical sample about 7–10 days, and bulk production 12–18 days after sample approval. Packing adds 2–3 days. Timelines are confirmed per order once the artwork is reviewed.
Butterfly clutch is standard. Rubber clutch, double post (for larger pins that must not rotate), magnetic back and safety-pin style are available on request. Double post is recommended above 40 mm to keep the pin flat against fabric.
Yes, we match to the nearest achievable enamel reference and show the match on the digital proof. Enamel is a baked pigment system, so a small tolerance against a printed Pantone chip is normal; approval is based on the proof and the physical sample.
Yes. Options include OPP bag, kraft backing card with a punched hole for pegboard display, printed display card with your logo, and barcode or sticker labels supplied by you. Packing instructions are confirmed before the bulk run.
Nickel-free and low-nickel plating routes are available on request for markets with specific requirements, and should be stated at inquiry stage so it is built into the quotation and the proof.
Orders ship by express, air or sea freight depending on volume and destination. EXW, FOB and DDP terms can be quoted on request; the option is confirmed with the invoice so duties and delivery responsibility are clear before dispatch.
Production is checked against the signed-off sample before packing. If a deviation is found during inspection, the affected pieces are reworked or remade before shipment, and the inspection result is shared with the buyer.
Tell us the quantity, size and plating you need. You will receive a digital proof, a per-piece price at your quantity and an indicative production schedule — before any tooling commitment.
Replace the contact link and company details with your own before publishing. Minimum order 50 pieces per design. Prices quoted per order based on size, color count, plating and packaging.